Hand Engraving
Tools for Engravers, Jewelers & Metal Artists


AirGraver® Patent & Trademark Information

Warranty & Voiding

CATALOG INDEX - CLICK HERE

Lindsay AirGravers & PalmControls
Graver Sharpening
Graver Blanks
Engraving Vises
Engraving Accessories

Engraving Sets
Manual Operated Engraving Tools
Air Compressors

Microscopes
Books
On-line Resources

Coin Carving

Home Page

About:
   Hand Engraving
   Lindsay Airgravers
   Evolution of AirGraver
   Lindsay Graver Point
   Artisan AirGraver®
   Classic AirGraver®
   PalmControl®
 


Feedback:
   Testimonials
   Phil Coggan
   Roland Baptiste
   Andy Shinosky
   Adone Pozzobon
   Delivery & Service
 

News
Gallery
Videos
EngravingForum.com

Contact - Email

Engraving Resources
EngravingForum.com
   Free online engraving   
       books and videos

   EngravingClasses.com
   EngravingGlossary.com
   EngravingSchool.com

 

ARTISAN AirGraver®

The Artisan AirGraver® has a patent pending improved collet design that helps the tool deliver impacts more efficiently. The tool is a work horse for jewelers. Speed range: 2400 at idle through 10,000 at 60 PSI when used with the included stainless piston. When used with a tungsten dead blow piston; 1500 at idle through 7,000 at 60 PSI. Three handpiece tubing attachment locations for customability and comfort. Non-slip rubber handle.

Nose collets are S7 tool steel, hardened and tempered to 57 Rockwell. Cylindrical precision ground for a life time of service.

Includes: Stainless body, two quick change collets, two high speed graver blanks (not sharpened), supple black rubber handle. The tool uses the same dead blow bore and pistons as the Classic AirGraver® handpiece for interchangeability and also includes a hex wrench, handpiece tubing and fitting, and owner’s manual.

The Artisan handpiece does not have the patented stroke adjustment. Additional power if needed is attained by purchasing a tungsten dead blow piston.

Click for More information about Lindsay AirGravers.

Artisan AirGraver® Handpiece (comes with stainless piston): $595
Note: You will need the foot controller below for operating the Artisan Handpiece. 

add_to_cart.gif

Additional Collets: $25 each

add_to_cart.gif

AirGraver® foot control, idle adjust with double regulators: $249
This item can only be ordered together with an AirGraver handpiece.

add_to_cart.gif

    view_cart.gif

Custom Amboyna Burl Handle for foot control AirGraver®.  These burl handles will fit on foot controled Classics, Aritisans and NitroG90s.

$199


Gun Engraving by Carl Bleile with Artisan AirGraver® Click to enlarge


Keeping the overall price down on an engraving system

The Artisan hand piece together with foot control, idle adjust regulators is $844. This is the least expensive AirGraver® , together with a tungsten piston it is more versatile in power and speed than any competitor's top-end product. Top end power with the stainless piston is reached around 60psi where as the tungsten piston can be taken up to 80psi. The tungsten will really will kick-in up in that psi.

If desiring to keep the overall price down of a system an air compressor can be expensive.  However, because the AirGraver®s do not require very much air volume, the smaller inexpensive compressors work fine. Ace hardware and Wal-Mart carry a $59 compressor as well as a $99 one.  They aren't as quiet as the Silentaire compressor but other than the noise they do fine.  One way around the noise problem is to place the compressor in another room or in your garage and run an air line through the wall.

Below is a chart.  It shows the various impact speeds at different stroke adjustments of the Classic handpiece. The Artisan doesn't have this stroke adjustment but is fixed at the mid stroke length. Follow the "Medium Stroke" speeds on the chart to see the speed ranges for the Artisan. The tungsten piston also works in the Artisan and there is a column for that. Follow the medium stroke column there too. For both the Artisan and the Classic the PSI  ranges are adjusted with the foot control or the PalmControl® handle.

At Browning I have taught people to engrave that wanted to learn the art and absolutely fell in love with the Lindsay AirGraver®. Also, I have let non-engravers play with it and guess what, they starting cutting with no problem.
Rich Hambrook, Browning Arms Company                        Additional Feedback

 

 

   

 

Translate Site to Language
Arabic Japanese
Chinese Korean
French Portuguese
German Russian
Italian Spanish

Sister Sites:
www.EngravingForum.com
www.EngravingLessons.com
www.EngravingSchool.com

www.HandEngravingClasses.com
www.EngravingGlossary.com
www.LindsayEngraving.com
Contact - Email