NitroG20™
AirGraver™
For deep engraving as used in
Motorcycle and Heavier Western Engravings
The NitroG20 will work with either a foot control or with a PalmControl handle. It has a larger and
longer internal bore and piston than the Classic or Artisan handpieces. The NitroG20 comes standard with a heavy 20gram Tungsten piston. Price of
the handpiece and tungsten piston is $995. For $75 additional it will have the L slots milled on the back of the body so that a PalmControl handle
will fit and snap on and off of it. CFM air volume requirement to run the tools is 0.9 CFM at 70 to 90PSI. The Supersilent 20-A compressor is too
small. The Supersilent 50-TC is large enough though as it outputs 2.0CFM at 84PSI to 114PSI. Other compressors that can out put at least
.90CFM at 80PSI should work fine with the tool. The tool can also be run with a 80psi CO2 regulator either in a foot control setup or PalmControl setup.
The 80PSI CO2 regulator is listed below.
The NitroG20 is included with one presharpened M42, one M42 graver blank, two HSS graver blanks, handpiece tubing wrenches
and an owners manual.
Carl Bleile - Master Engraver NitroG90 AirGraver Video
Check out Carl Bleile many engraving tutorials at EngravingLessons.com
Recommended operating PSI for the NitroG20 is 70 to 90 PSI. See below about upgrading your air regulator
gauge and/or CO2 regulator.
Below: Comparison of a 20gram NitroG20 Tungsten piston and a 7 gram Classic Tungsten piston
NitroG20™
handpiece for a foot control. If you already have a foot control Artisan or Classic this handpiece will run off your current foot control
setup.
The tool holder in this tool will hold 3/32" square and 1/8" round graver shanks as well as other shanks that
will fit within a .133" diameter hole. If you would like to order the handpiece to hold larger 1/8" square and 3/16" round shanks please
write a note saying so in the add to cart "check out" page.
$995
This option provides the NitroG20™ handpiece with L slots milled on back of the body so that if you already own a PalmControl Classic you can use your PalmControl handle on the
NitroG20. The tool is shipped without the black rubber handle shown above so that you can fit your PalmControl directly on the tool when it arrives.
The tool holder in this tool will hold 3/32" square and 1/8" round graver shanks as well as other shanks that
will fit withing a .133" hole. If you'd like the handpiece setup to hold 1/8" square and 3/16" round shanks please write a note in the add to cart "check
out" screen.
$1,070
The tool holder in this tool will hold 3/32" square and 1/8" round graver shanks as well as other shanks that
will fit withing a .133" hole. If you'd like the handpiece setup to hold 1/8" square and 3/16" round shanks please write a note in the add to cart "check
out" screen.
NitroG20™ PalmControl™ handpiece. The tool can be purchased with
four different handle materials:
1:Ivory color Santoprene
2:Burl wood
3:Stainless steel
4:Damascus
The tool is included with one presharpened M42, one M42 graver blank, two HSS graver blanks, handpiece tubing wrenches
and an owners manual.
Option #1
$2,690
Option #2
$2,890
Option #3
$2,749
Option #4
$3,110
If you already have an AirGraver air regulator you will notice the display on the gauge only goes to 60PSI and so you'll
need this replacement gauge in order to run the NitroG20 at the recommend air pressures of 70 to 90PSI. Simply unscrew your old gauge and screw in
this replacement that displays up to 100PSI.
$14
0-80 PSI CO2 High Pressure Regulator. This is a higher PSI
CO2 Regulator for operating your NitroG20. Also works with Classic and Artisan handpieces.
CO2 80PSI Regulator
$172
20oz paintball cylinder adapter$38
CO2 Regulator
$172
20oz Adapter $38
CO2 Foot Pedal AirGraver™ Controller
(for NitroG20)
Includes high PSI CO2 regulator, foot pedal lines, on/off toggle, idle adjust valve and CO2 adapter for using common 20oz CO2 cylinders that are also
used by paint ball guns. One 20oz bottle will last approximately three to four hours with a foot pedal NitroG20.
Click photo to enlarge
Updating a foot control NitroG20™handpiece to PalmControl™-$1790 If you would like to update your foot control NitorG20 to PalmControl order this upgrade, and we will contact you when we have a PalmControl
handle made for you. (usually 5 to 10 working day) We will then contact you and you can send your handpiece in for the updated then. The
update will only take couple days this way so you'll be without it for a shorter amount of time.
$1,790
Custom Amboyna Burl Handle for foot control AirGraver. These
burl handles will fit on foot controled Classics, Aritisans and NitroG90s.
$199
Handle materials for the PalmControl can be
purchase separately.
